Account Contact
Je winkelwagen
DPD & FedEx – bezorgdatum op de productpagina.
Hulp nodig? DistriNode AI helpt je met alles op onze site.

Moederbord (AD5X IFS) voor Flashforge 3D-printer — reserveprintplaat, MPN 20004780001

Moederbord (AD5X IFS) voor Flashforge 3D-printer — reserveprintplaat, MPN 20004780001
Moederbord (AD5X IFS) voor Flashforge 3D-printer — reserveprintplaat, MPN 20004780001
23,22 €
PDF
PDF

Bezorging & retourneren

Verwachte bezorgdatum donderdag 10 december
Je blijft op de hoogte via ons uitgebreide trackingsysteem
Betaalopties
BetaalkaartVisaMastercardPayPalApple PayGoogle PayBankoverschrijving

Omschrijving

The Main Board (AD5X IFS) for Flashforge 3D Printer is a replacement control PCB designed to manage the printer's core electronics. It integrates signal routing for stepper motors, endstops and sensors, heater and fan control, and communication interfaces between the printer's firmware and hardware. Intended as a direct replacement for a defective main board, this unit restores control of motion, temperature regulation and peripheral devices to recover printing capability.

Advantages

This replacement main board provides the same functional layout and connections as the original Flashforge control board, enabling straightforward swap-in installation. It supports coordinated control of motors and heaters, accurate sensor inputs for temperature and position, and stable power distribution to maintain reliable printing operations. Using a compatible board reduces downtime and avoids the need for full printer replacement.

Suitable for

  • Repairing a Flashforge 3D printer with a faulty or damaged main control board
  • Restoring lost functionality after electrical failure or component damage
  • Replacing a burnt or non-responsive PCB to resume normal printing

Key specifications

  • Function: central control PCB for 3D printer electronics
  • Controls: stepper motor drivers, endstop and sensor inputs, heater and fan outputs
  • Interfaces: standard board connectors for thermistors, heaters, fans, motors and control panel
  • Power handling: designed for typical desktop FDM printer voltages and loads
  • Form factor: replacement board sized to fit the corresponding Flashforge chassis and mounting points
  • Compatibility: intended for direct replacement in compatible Flashforge models

How to use

Power down the printer and disconnect it from mains supply before beginning any replacement. Remove the printer cover to access the controller area, note or photograph existing cable routing and connector positions, then disconnect cables from the old main board. Unscrew and remove the faulty PCB, install the replacement board aligning mounting holes and connectors, and reconnect all wiring according to the recorded layout. Reassemble the enclosure, reconnect power, and perform initial power-on checks. Verify thermistor readings, heater activation, endstop recognition and motor movement through the printer's control interface before starting a print.

Recommendations

Use only the specified board layout and connector types to avoid mismatches. Inspect cables and connectors for damage and replace any worn wiring. After installation, calibrate axis endstops and temperature settings, and run a test print to confirm stable operation. If unsure about wiring or firmware compatibility, consult the printer service manual or seek professional technical support.

Belangrijkste kenmerken
  • Repairing a Flashforge 3D printer with a faulty or damaged main control board
  • Restoring lost functionality after electrical failure or component damage
  • Replacing a burnt or non-responsive PCB to resume normal printing
  • Function: central control PCB for 3D printer electronics
  • Controls: stepper motor drivers, endstop and sensor inputs, heater and fan outputs
  • Interfaces: standard board connectors for thermistors, heaters, fans, motors and control panel
  • Power handling: designed for typical desktop FDM printer voltages and loads
  • Form factor: replacement board sized to fit the corresponding Flashforge chassis and mounting points
  • Compatibility: intended for direct replacement in compatible Flashforge models
Prijsverloop van de afgelopen 6 maanden
Moederbord (AD5X IFS) voor Flashforge 3D-printer — reserveprintplaat, MPN 20004780001
Actueel
23,22 €
Laagste 7 d
22,93 €
Hoogste 7 d
23,22 €
Wijziging 24 uur
+0,29 €   +1%
Wijziging 7 d
—   
Wijziging 30 d
—   

Review schrijven

Beoordeling *
Opmerking: HTML wordt niet omgezet!

Dezelfde serie en alternatieven

12

Populaire producten in deze categorie

8
Verkoper / Vendeur : UAB KUR LT · Gariūnų g. 57-14, LT-02300 Vilnius, Litouwen / Lituanie · Ondernemingsnr. / N° d’entreprise 303192950 · Btw-nr. / N° TVA LT100008198612 · Verzending vanuit de EU (Litouwen) / Expédition depuis l’UE (Lituanie)
WhatsApp
Messenger
Hoi, ik ben de AI-assistent van DistriNode. Ik help je graag met het vinden van producten, het vergelijken van opties, het maken van offerte-PDF's of het openen van supportaanvragen.
Alle categorieën